Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| mozaic_tips_and_tricks [2020/11/17 02:15] – Formatting _ki | mozaic_tips_and_tricks [2021/04/12 17:43] – [Remove or add an entry inside an array] _ki | ||
|---|---|---|---|
| Line 18: | Line 18: | ||
| * [[#Use a Knob to toggle 16 Pads View to HELP View]] | * [[#Use a Knob to toggle 16 Pads View to HELP View]] | ||
| * [[#Knob double-tap Support]] | * [[#Knob double-tap Support]] | ||
| + | * [[#Remove or add an entry inside an array]] | ||
| * [[#Using Logic Operators in Expressions instead of IF cases]] | * [[#Using Logic Operators in Expressions instead of IF cases]] | ||
| * [[#Using Inc and Dec in Expressions]] | * [[#Using Inc and Dec in Expressions]] | ||
| Line 84: | Line 85: | ||
| varB = 124 // allowed range 0 .. ~16000 | varB = 124 // allowed range 0 .. ~16000 | ||
| | | ||
| - | combinedValue = valA + valB * maxA | + | combinedValue = valA + (valB * maxA) |
| </ | </ | ||
| + | |||
| + | For single-byte MIDI values, use 128 for maxA | ||
| To later extract the values from their packed format use | To later extract the values from their packed format use | ||
| Line 145: | Line 148: | ||
| f = Div n, 10 | f = Div n, 10 | ||
| r = (n-f*10) % 10 | r = (n-f*10) % 10 | ||
| - | if number>=0 | + | if value >=0 |
| LabelKnob 1, {N: +},f,{.},r | LabelKnob 1, {N: +},f,{.},r | ||
| else | else | ||
| - | LabelKnob 1, {N: +},f,{.},r | + | LabelKnob 1, {N: },f,{.},r |
| endif | endif | ||
| </ | </ | ||
| Line 382: | Line 385: | ||
| + | \\ | ||
| + | ===== Remove or add an entry inside an array ===== | ||
| + | < | ||
| + | Instead of running through an array with a FOR loop to shift entries to either insert or remove an intermedeate enry, it is way faster to use the CopyArray Mozaic function: | ||
| + | |||
| + | < | ||
| \\ | \\ | ||
| + | === Remove an entry of an array (shift left) === | ||
| + | |||
| + | < | ||
| + | @OnLoad | ||
| + | for i=0 to 6 | ||
| + | a[i] = i | ||
| + | endfor | ||
| + | Log {Before },a[0],{ },a[1],{ },a[2],{ },a[3],{ },a[4],{ },a[5],{ },a[6] | ||
| + | |||
| + | // Remove entry a[2] by left shift of the following entries | ||
| + | CopyArray a[3], a[2], 6 | ||
| + | | ||
| + | Log {After | ||
| + | @End | ||
| + | </ | ||
| + | |||
| + | \\ | ||
| + | === Insert an entry into array (shift right) === | ||
| + | |||
| + | Due to the inner working of CopyArray, the above trick doesn‘t work for right shifts - but one can use a temporary array to be more efficient than iterating over the array: | ||
| + | |||
| + | < | ||
| + | @OnLoad | ||
| + | for i=0 to 6 | ||
| + | a[i] = i | ||
| + | endfor | ||
| + | Log {Before | ||
| + | |||
| + | // Insert a new a[2] | ||
| + | CopyArray a[2], _tmp, 6 | ||
| + | CopyArray _tmp, a[3], 6 | ||
| + | a[2] = 9 | ||
| + | | ||
| + | Log {After | ||
| + | @End | ||
| + | </ | ||
| ===== Using Logic Operators in Expressions instead of IF cases ===== | ===== Using Logic Operators in Expressions instead of IF cases ===== | ||
| < | < | ||
_ki